A
Weaver type rail that extends from the rear of the slide to
just forward of the slide ejection port. A steel insert that
replaces the rear sight has a recoil bar that mates to the
rail. A flat head screw holds rail in place. The rail also
has a "Giles" type ejection port. This mount is
for target loads only.
$85.00
Daisy
DA-L
A
Weaver type rail that clamps onto the barrel of the Daisy
models 717,737, and 777. It has an extension rail that extends
back almost to the loading port. Weight is approx 4.5 oz.
$74.00
Feinwerkbau
AW-93
A
Weaver type rail that can allow optics to be left permanently
on and be removed for slide removal with minimum zero impact.
Has a vee block to capture the rear sign pivot pin and a dovetail
feature to replace the front sight. A set screw at the vee
block adjusts the fit in the rear sight channel. A single
set screw locks the rail on to the pistol
$103.00
Hammerli
HAM207R
A
full length Weaver type rail for the Hammerli model 207 that
attaches at the front and rear sight locations. Dovetails
at the front and rear allow for removal for cleaning with
little or no change in point of impact. Has ejection cut-out
for aid of ejection. Weight approx. 3.5 oz.
A
full length Weaver type rail for the Hammerli model 210 that
attaches at the front and rear sight locations. Similar to
the HAM207 and HAM208S mounts.Weight approx. 3.7 oz.
A
Weaver type rail for the 32 cal. Hammerli 280. The rail extends
back almost to the rear sight. It attaches by replacing the
2 rear most barrel weights. Weight approx. 5 oz.
A
set of rings (2 per set) that simultaneously clamp a High
Standard .90 inch diameter bull barrel and a 30 mm optical
sight. Weight approx. 2 oz.
$51.50
HS-FL
A
Weaver type rail for the High Standard Fluted barrel. It attaches
by a dovetail that replaces the front sight and a clamp that
clamps the barrel just forward of the "take down button".
Weight appox. 4 oz.
$98.00
HS-FLS
A
Weaver type rail for the High Standard 5.5" bull barrel
It attaches by a dovetail that replaces the front sight and
a clamp that clamps the barrel just forward of the "take
down button". Weight appox. 3 oz.
A
Weaver type rail direct replacement for the High Standard
5.5 inch Victor model rib. Has relief in the ejection area
for positive ejection. Proper screws supplied. Weight approx.
3.5oz.
A
Weaver type rail incorporated in an aluminum barrel shroud.
Reduced weight is an advantage.The original barrel and shroud
must be sent to BME for fitting. Weight approx. 6 oz.
$155.00
Ruger
RU-RS
A
Weaver type rail for the Ruger Mark I &II models that
replaces the rear sight. Weight approx. 2 oz.
$77.00
RU-TAP
A
Weaver type rail that clamps onto the tapered barrel of tapered
barrel Rugers. Weight approx. 4 oz.
Similar
to the S&W52-RR. Has a dovetail for the newer S&W41
with Millett rear sight Weight approx. 2 oz.
$77.00
S&W952-R
Weaver rail for the S&W952 that is similar to the S&W52-RR
except it has the Wilson Recoil Bar and screw for attachment.Weight
approx.2.5 oz.
$77.00
S&W52-2000B
A
dovetail base for the Tasco Optima 2000 optics that fits the
S&W52. Weight approx.1 0z.
$40.00
S&W945-R
A
Weaver type rail that replaces the rear sight of the S&W945.
A steel insert that replaces the rear sight has a recoil bar
that mates with the rail. It is held in place with a flat
head screw. The rail also has a "Giles" type ejection
port. This mount is for target loads only
A
Weaver rail for the Walther Expert Model. It has the 3 weaver
ring locations forward of those on the WA-PR3C model. It attaches
in the same manner as the WA-A. Weight approx. 2 oz.
A
Weaver type rail for the Unique model 69 that has a clamping
block that clamps the barrel in the same manner as the barrel
weights. Weight approx. 4 oz.
$99.00
UN-69U-R
A
Weaver type rail for the Unique model 69U. Is similar to the
UN-69-R except it has a pressure plate like the model 69U
barrel weight. Weight approx. 4 oz.
$99.00
UN-96
A
Weaver type rail for the Unique model 96. The rail swings
the optics out of the way to allow insertion and removal of
the magazine. It attaches at the front sight dovetail and
rear sight cross pin. Weight approx. 6 oz.
$140.00
Smith
& Wesson
S&W952-2000
A
Wilson Recoil Bar base for the Tasco Optima 2000 optics that
fits the S&W952. Weight approx. 1 0z.
